Full system diagnostic
We test refrigerant charge with manifold gauges, check electrical components with a clamp meter, and inspect the blower motor, capacitors, and contactors. You get a clear explanation of what failed and why.
Licensed, insured techs who fix it right the first time
HVAC repair near me Milwaukie OR - same-day service you can count on
When your furnace quits on a 28-degree night or your AC blows warm air in July, you need HVAC repair near me Milwaukie OR that shows up fast. ThermexaPro serves homeowners across Milwaukie, Oregon and Clackamas County with same-day diagnostics, upfront pricing, and repairs done to code. We stock the parts your system needs.
Careful work. Honest options.
About this service
What HVAC repair near me Milwaukie OR actually covers
HVAC repair near me Milwaukie OR is the diagnostic and repair work that gets your heating, cooling, or ventilation system running again after a breakdown, strange noise, or temperature failure. That means tracing the fault with manifold gauges and a multimeter, checking refrigerant charge on your R-410A or R-22 system, testing capacitors and contactors, and confirming your blower motor is moving the right CFM. We repair Carrier, Trane, Lennox, Goodman, Rheem, York, Mitsubishi Electric, and Daikin equipment, and we work on Nest and Ecobee thermostats too.
Milwaukie homes take a beating from wet winters and hot, dry summers. Furnaces that sat idle since March often fail on the first cold snap, and AC units that ran through August develop refrigerant leaks or frozen evaporator coils. When you search Milwaukie OR HVAC repair near me, you want a tech who knows this climate. We also clear clogged condensate drains, replace dirty air filters, and repair duct leakage that wastes 20 to 30 percent of your conditioned air.
- ✓ Same-day service, not next week
- ✓ Upfront pricing before we start
- ✓ Licensed, bonded, and code-correct
- ✓ 3 years serving Clackamas County
What's included
What our HVAC repair near me includes
Every repair visit starts with a full diagnostic and ends with a tested, running system. Here is what is covered in a standard call, and what we quote separately if your job needs it.
Common part replacement
Capacitors, contactors, igniters, flame sensors, thermostats, and blower motors are stocked on our vans. Most replacements finish the same visit, usually within 1 to 3 hours of arrival.
Refrigerant leak repair
We locate leaks with an electronic detector, repair the line or fitting, then recharge your R-410A or R-22 system to factory spec. We verify the charge with gauges before we leave.
Drain and airflow service
Clogged condensate drains and dirty filters cause a large share of no-cool calls. We clear the PVC line, check the drain pan, and confirm airflow so the system runs at the right CFM.
Post-repair test cycle
We run the system through a full heating or cooling cycle and record supply and return temperatures. You see the numbers that prove the repair worked before we pack up.
How it works
What to expect when you call
You call (855) 947-9500 and tell us what is happening: no heat, no cool, weird noise, water on the floor. We ask a few quick questions to figure out whether this is a repair or an emergency, then book a same-day window that fits your schedule.
A NATE-certified tech arrives in a stocked van, typically within 2 to 4 hours. He runs a full diagnostic with manifold gauges, a clamp meter, and a leak detector, then shows you exactly what failed and what it costs to fix. You approve before any work starts.
Most repairs take 1 to 3 hours. We replace the failed capacitor, contactor, blower motor, or refrigerant charge, then run the system through a full heating and cooling cycle to confirm temperatures and airflow hit spec. We clean up and haul away old parts.
Before we leave, we walk you through what we fixed and show you the readings. We check your air filter, note the size you need, and point out anything else that looks worn. You get a written summary of the work and the parts we installed.
Every repair carries a workmanship warranty. If the same problem comes back within the warranty window, we return at no charge. We also send a reminder when your next pre-summer AC tune-up or winter furnace tune-up is due.
STEP 01Call and describe
You call (855) 947-9500 and tell us what is happening: no heat, no cool, weird noise, water on the floor. We ask a few quick questions to figure out whether this is a repair or an emergency, then book a same-day window that fits your schedule.
Tools & methods
Tools and methods we use
Manifold gauges
Used to read high-side and low-side refrigerant pressures on R-410A and R-22 systems. The readings tell us whether the charge is correct or whether there is a leak.
Electronic leak detector
Pinpoints refrigerant leaks at fittings, Schrader valves, and coil joints. Finding the leak first prevents us from recharging a system that will just leak again.
Clamp meter and multimeter
Tests capacitors, contactors, and blower motor amp draw. These readings confirm whether a component has failed or whether the problem is upstream in the control board.
Vacuum pump and recovery machine
Used when a repair requires opening the refrigerant circuit. The recovery machine captures refrigerant per EPA rules, and the vacuum pump pulls the system down before recharging.
Fin comb and duct cleaning vacuum
Straightens bent condenser fins and clears debris from ductwork. Both improve airflow, which is one of the most common causes of weak heating and cooling.
Real results
Before and after.
HVAC repair near me
No-heat furnace fixed in one visit
A homeowner in Oak Grove woke up to a 54-degree house in late November. The furnace was running but blowing cold air. The previous company quoted a full furnace replacement at $4,800.
After: We diagnosed a failed hot surface igniter and a dirty flame sensor. Both parts were on the van. Total repair: $310, completed in 90 minutes. The furnace fired and held 68 degrees through the night.
Book this service →
HVAC repair near me
AC restored after refrigerant leak repair
An Ardenwald homeowner's AC ran constantly but the house would not drop below 79 degrees in August. The system was 6 years old and low on R-410A, but nobody had found the leak.
After: We located a leaking Schrader valve with an electronic detector, replaced the valve, pulled a vacuum, and recharged the system to factory spec. Supply air dropped from 68 to 55 degrees. The repair cost $540.
Book this service →
HVAC repair near me
Condensate drain clog stopped water damage
A Downtown Milwaukie condo owner found water pooling around the furnace cabinet. The condensate drain had clogged with debris, and water was backing into the unit and onto the floor.
After: We cleared the PVC drain line, flushed the trap, and replaced a cracked section. We also tested the float switch. The leak stopped, the floor dried, and no drywall repair was needed. Cost: $220.
Book this service → Problems we solve
HVAC problems we fix in Milwaukie
Most calls we get fall into a handful of categories. Here is what typically goes wrong, what it costs you if you wait, and how we fix it.
Ask a pro →Furnace not heating on a cold morning
We test the igniter, flame sensor, gas valve, and control board, then replace the failed component. Most no-heat calls are fixed with a part we carry on the van, and you have heat the same day.
AC not cooling during a heat wave
We check refrigerant charge, capacitors, contactors, and the evaporator coil. If the system is low on R-410A, we find the leak, repair it, and recharge to spec. Most AC repairs finish same day.
Refrigerant leak draining efficiency
We locate the leak with an electronic detector, repair the line or fitting, then recharge the system and verify the charge with manifold gauges. You get the pressure readings in writing.
Clogged condensate drain causing water damage
We clear the line, flush the trap, and replace any cracked PVC sections. We also check the drain pan and float switch so the system shuts off safely if it clogs again.
Proof you can check
Licensed, certified, and reviewed
- NATE Certification · North American Technician Excellence
- EPA Section 608 Certification · U.S. Environmental Protection Agency
- Oregon CCB License · Oregon Construction Contractors Board
- OSHA Safety Compliance · Occupational Safety and Health Administration
Most repairs run $180 to $650, including the diagnostic. A capacitor or contactor swap sits at the low end; a blower motor or refrigerant leak repair lands higher. Emergency calls after hours add a dispatch fee. You get the exact price in writing before we start, and the diagnostic fee is waived if you approve the repair.
ThermexaPro does, and we have been doing it since 2023. We are Oregon CCB licensed, NATE certified, and EPA Section 608 compliant. We serve all of Milwaukie plus Oak Grove, Gladstone, Oregon City, and the surrounding Clackamas County area. Call (855) 947-9500 and we will book a same-day window.
Yes. We run 24/7 emergency dispatch for no-heat and no-cool calls. If your furnace dies at 2 a.m. in January or your AC quits during a July heat wave, call us and we will get a tech rolling. Most emergency calls in Milwaukie get a technician on site within 90 minutes to 3 hours.
Start with a company that is licensed in Oregon, carries NATE certification, and quotes a flat price before working. Ask whether they stock common parts on the van and whether they handle your brand. Then check that they serve your neighborhood, whether that is Ardenwald, Linwood, or Downtown Milwaukie. We check every one of those boxes.
Ready when you are
Get HVAC repair near me Milwaukie OR today
Same-day service, upfront pricing, and a workmanship warranty on every repair. Our line is open 24/7 for no-heat and no-cool emergencies. Call now and we will book your window.
Book a repair (855) 947-9500 →
Request an appointment
Contact ThermexaPro in Milwaukie
Call (855) 947-9500 any time, day or night, and a live dispatcher will get a tech headed your way. Regular office hours run 8 a.m. to 6 p.m. Monday through Friday, with 24/7 emergency coverage for no-heat and no-cool calls. You can also email info@thermexapro.com and we will reply the same business day.
Call anytime(855) 947-9500Email the officeinfo@thermexapro.shop
Office hoursOpen 24 hours · 7 days a week